DCPPE-200 資格取得 & Dell PowerEdge Professional

 

我々は、失敗の言い訳ではなく、成功する方法を見つけます。あなたの利用するDellのDCPPE-200 資格取得のソフトが最も権威的なのを保障するために、我々JPexamの専門家たちはDellのDCPPE-200 資格取得の問題を研究して一番合理的な解答を整理します。DellDCPPE-200 資格取得の認証はあなたのIT能力への重要な証明で、あなたの就職生涯に大きな影響があります。

当代社会の競争が激しいとともに、自分の生きがいを探すために、できるだけ自分の能力を生かさなければならない。IT業界でのあなたは自分の能力を高めるために、DCPPE-200 資格取得を準備しているのでしょう。我々はDCPPE-200 資格取得に参加するつもりのあなたに最高のサービスを提供します。我々の提供するDCPPE-200 資格取得を利用して、あなたは試験に合格することができると信じています。

DCPPE-200試験番号:DCPPE-200問題集
試験科目:Dell PowerEdge Professional
最近更新時間:2017-05-31
問題と解答:全65問 DCPPE-200 テスト内容
100%の返金保証。1年間の無料アップデート。

>> DCPPE-200 テスト内容

 

あなたに安心にネットでDellのDCPPE-200 資格取得の資料を購入させるために、我々JPexamは国際の最大の安全的な支払システムPaypalと協力してあなたの支払の安全性を保障します。支払ってから、あなたは直ちにDellのDCPPE-200 資格取得の資料をダウンロードすることができ、その後の一年間でDellのDCPPE-200 資格取得が更新されたら、我々はあなたを通知します。JPexamを選ぶのは最高のサービスを選んだことです。

NO.1 An engineer needs to configure server 1 to communicate on tagged VLANs 10, 20, and 30 and
untagged VLAN 50.
The server is in SLOT 1 of an FX2s chassis with two FN410s IOAs. The switches are currently set to
default settings.
Which command should be entered in each IOA to perform the engineer's task?
A. interface range vlan 10, vlan 20, vlan 30, vlan 50 no shut interface Ten GigabitEthernet 0/1
switchport vlan tagged 10,20,30 default vlan-id 50
B. interface range vlan 10, vlan 20, vlan 30, vlan 50 no shut interface Ten GigabitEthernet 0/1
portmode hybrid switchport vlan tagged 10,20,30
C. interface range vlan 10, vlan 20, vlan 30, vlan 50 no shut interface Ten GigabitEthernet 0/1
portmode hybrid switchport vlan tagged 10,20,30 vlan untagged 50
D. interface range vlan 10, vlan 20, vlan 30, vlan 50 no shut interface Ten GigabitEthernet 0/1
switchport vlan tagged 10,20,30 default vlan 50
Answer: C

DCPPE-200 真実   

NO.2 An engineer is migrating an existing server node from an M1000E to a VRTX chassis.
An error message appears during POST. The system will continue to boot, but can NOT see any of the
chassis shared storage or PCle devices mapped to the server slot.
The engineer has already removed the original fabric interfaces in mezzanine slot Band C from the
original system configuration .
Which action must the engineer complete to allow the node to see chassis storage and mapped PCle
devices?
A. Remap chassis storage/PCle devices
B. Update the CPLD firmware version
C. Install PCle Pass-Through mezzanine cards
D. Enable PCle Pass-Through in System Setup
Answer: D

NO.3 In VRTX the following features are enabled:
1 . Server Module Firmware Update
2 . Remote syslog
3 . iDRAC Single Sign-on.
4 . Server configuration
5 . Chassis grouping
6 . Enclosure level backup
Which license type is required?
A. iDRAC express license
B. CMC enterprise license
C. CMC express license
D. iDRAC enterprise license
Answer: B

DCPPE-200 クラムメディア   

NO.4 Refer to the exhibit.
An engineer needs to configure iSCSI boot on a blade.
iSCSI boot is NOT working.
Which two steps should the engineer take to fix the issue? (Choose two.)
A. Change the IQN of the initiator
B. Update the DNS server entries on the initiator
C. Modify the boot LUN ID on the target
D. Verify the IP address of the target and initiator
E. Validate default gateway settings on the initiator
Answer: B,E

DCPPE-200 独学   

JPexamは最新の070-534問題集と高品質の300-209問題と回答を提供します。JPexamの70-698 VCEテストエンジンとRAC-US試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質の70-480 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100%保証します。試験に合格して認証資格を取るのはそのような簡単なことです。

記事のリンク:http://www.jpexam.com/DCPPE-200_exam.html